Model WC33IENGLISH ... 2FRANÇAIS ... 17ESPAÑOL... 33In
- 10 -INSTALL FLUE MOUNTING BRACKETDUCTED OR NON-DUCTED1. Assemble the flue mounting bracket, adjusting outside width as shown. Fig. 10.2. Care
- 11 -FIG.12DAMPER6-INCH DIA.METAL DUCTDUCTED INSTALLATION ONLY1. Press the damper into the duct connector on the hood. Fig. 12.2. Run 6-inch d
- 12 -NON-DUCTED INSTALLATIONWITH FLUE 1. Do not install damper supplied with the range hood.2. Attach the 5” to 6” adapter to blower discharge and
- 13 -5. Plug power cord into wall outlet.6. Temporarily secure the upper and lower flue together with duct tape as shown. Fig. 18.7. Lift the
FIG. 20FIG. 21- 14 -3,9 x 6 mm.SCREWSINSTALLATION BLADE GUARDONLY FOR NON-DUCTED HOODSWITHOUT FLUENote: Purchase Model ANKWC33Non-ducted Recirculation
- 15 -ADJUST HOOD HEIGHT1. Loosen (3) screws on upper decora-tive trim. Fig. 22.2. Slide trim up to increase panel open-ing from 13-3/4” to 14-3/8”.
- 16 -INSTALL FILTERSDUCTED AND NON-DUCTED HOODS1. To remove the GREASE filter, push in latch tab to disengage the filter from the hood. Tilt the fil
- 17 -KEY NO.59141626373845484953586062678692107114118119120122130147154166167223228230234340341342407415474503-----PART NUMBERB08092926B08087824B0230
- 18 -SERVICE PARTS16120671141225886119118621541074742694153411303423409223438(W0000055)2232282304076016714716638(03295595)14495345485033799044738CCHA
- 19 -Modèle WC33IAux ÉTATS-UNIS - BEST Hartford, WisconsinAu CANADA - BEST Drummondville, QC, Canada ENREGISTREZ VOTRE PRODUIT EN LIGNE À L’ADRESSE:
- 2 -READ AND SAVE THESE INSTRUCTIONS WARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:1. Use this un
- 3 -! CAUTION1. For indoor use only.2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air int
- 4 -OPERATIONControlsThe hood is operated using the (5) push buttons located on the front edge of the hood. Fig. 1.The Light On/Off switch turns the
- 5 -HALOGEN BULBSThis range hood requires two halogen bulbs (Type T4, 120Volt, 25Watt Max, G9 Base). WARNING: Always switch off the electrical supp
- 6 -PREPARE THE HOODUnpack hood and check contents.You should receive:1 - Hood1 - Decorative Flue Assembly1 - Parts Bag containing: 2 - Mounting B
- 7 -ROOF CAP6-INCHROUND DUCTDECORATIVE FLUEHOODWALL CAP6-INCHROUND ELBOW24” TO 30” ABOVE COOKING SURFACE(see “INSTALL MOUNTING BRACKETS” section fo
- 8 -INSTALL MOUNTING BRACKETSDUCTED and NON-DUCTED HOODS1. Construct wood wall framing that is flush with interior surface of wall studs. Fig. 6
- 9 -DRYWALLANCHORSFIG. 9INSTALL THE HOODNote: Remove the plastic protective film from all exterior surfaces, deco-rative flues and filters, prior to
Comments to this Manuals