Best BHC56650XA User Manual download pdf (Page 2)

ENGLISH

The appliance must be installed by a qualified person in compliance with the instructions provided.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Only for hoods equipped with electronic control:

The 4th speed (intensive) is automatically lowered to 3rd speed after 5 minutes of operation to optimise energy consumption.

- If the hood is left on (lights and/or motor), after 10 hours in the absence of commands from the user, it will automatically

switch to OFF condition with all services switched off.

- The Buzzer emits a “beep” each time that a command is set from the keyboard or remote control (optional).

- In the event of interruption of power during the hood, if you restore the hood in the OFF state, then the engine must

be reactivate manually.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard.

DESCRIPTION

The unit can be found in filtering hoods or ducting hoods. In the Filtering version the air and the kitchen fumes that

are conveyed by the apparatus are depurated by the charcoal filter and put back into the room through the small grilles

of the ventilation flue (Fig. 1). ATTENTION: When using the filtering version, a charcoal filter and an air baffle (Fig. 1A)

must be used, which placed at the top of the structure, allows the air to recycle back into the room. In the Ducting version,

cooking vapours and odours are conveyed straight outside by a disposal duct which passes through the ceiling (Fig. 2).

INSTALLATION

ATTENTION: To install this appliance at least two people are necessary; therefore the installation work must be

undertaken by a qualified and competent personnel.

Disassembly of the grease filters: before proceeding to the installation of the appliance, remove the grease filters: pull

the handle outside and unlock the filter (Fig.3).

Separating the hood parts: separate the external part from the internal part by undoing the 6 screws (Fig. 4).

Fitting the seal: fit the seal on the round edge of the internal part (Fig. 5).

DUCTING VERSION ASSEMBLY

Before the installation of the appliance, it is necessary to arrange the air disposal duct.

Use a disposal duct which has:

- the minimum necessary length.

- minimum number of curves ( maximum curve corner: 90°).

- material approved by the State legislations; very smooth internal walls.

- Moreover we suggest you to avoid big changes to the pipe section (suggested diameter: 150 mm).

For the external air evacuation, follow all the other indications, as you can see in the “Warning” sheet.

Arrange the electrical feeding (for the electrical connection, follow all the other indications on the “Warning” sheet).

1. Draw a line on the wall, on the vertical of your cooking hob .

Draw on the wall the 6 holes you will make, according to the measures indicated in the Fig. 6; make the holes and insert

the dowels (Issued). As already specified in the “Warning” sheet , consider that the distance between the hood lower border

and the cooking hob must be min 650 mm.

2. Fit the plastic flange on the air vent of the motor, exercising slight pressure (Fig. 7).

3. Make the electrical connection. Connect the air exhaust pipe to the plastic flange using a bracket (pipe and bracket

not provided).

4. Take the external part of the hood (cylindrical body) and slide it in from the front until it touches the wall, then

push it upwards until it touches the ceiling (Fig. 8); secure it with 6 screws (use the 6 screws removed previously).

5. Fitting the control box. The controls differ depending on the model you have purchased.

To fit the controls shown in Fig.16 or Fig.17: fit the control box inside the cylindrical casing sliding it in sideways (Fig.

9). Lock it by tightening the 2 screws A.

To fit the controls shown in Fig. 18: secure the control box on the lower inside of the hood, fastening it with 2 screws (Fig.

10).

6. Connect the 2 halogen spotlights (Fig. 11).

7. Fit the sensor box (present only with certain models) in its seat, exercising slight pressure (Fig. 12).

8. Remember that for the ducting version the charcoal filter is NOT necessary, therefore, if it is installed, proceed

with removing it: grip the charcoal filter clip, push the filter towards the lower edge and then turn it towards the outside

of the hood (Fig. 13).

9. Refit the grease filter.

1 2 3 4 5 6 7 ... 27 28

Comments to this Manuals

No comments

Best BHC56650XA User Manual Page 2

Comments to this Manuals

Related products and manuals for Unknown Best BHC56650XA