Best K8087 User Manual download pdf (Page 5)

Page 5

ALLURE

QS2 SERIES

RANGE HOOD

INSTALL HOOD OPERATION

KEYHOLE (4)

MOUNTING SCREW (4)

1 Hang hood from (4) Mounting Screws. Slide hood towards

wall until mounting screws are engaged in narrow end of (4)

Keyholes. Tighten mounting screws securely. A long

screwdriver works best.

5 Replace filters, turn on power at service panel, and test for

proper operation.

3 Connect ductwork to hood. Use Duct Tape to make joints

secure and air tight.

DUCT

TAPE

2 Replace bottom cover.

PAR20,

50W MAX.

HALOGEN

BULB (2)

- or -

R16,

40W MAX.

INCANDESCENT

BULB (2)

4 Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16,

40 W Maximum

Incandescent Bulbs. Purchase bulbs

separately.

CAUTION: Bulbs may be hot! Refer to bulb packaging

for further information.

WARNING: To reduce the risk of electric shock, dis-

connect from power supply before cleaning.

Aluminum mesh filters: Clean frequently using hot water and a

mild detergent. Filters are dishwasher safe.

Charcoal filters: Clean filter surfaces frequently with a damp cloth

and a mild detergent. DO NOT immerse filters in water or put in

dishwasher. The special “Clean Sense” feature indicates when

the filter is to be replaced. The blue and yellow strips will blend to

green when it is time to change the filter. The “Clean Sense”

feature works best when facing toward the cooking surface.

To clean hood: Remove filters. Use a damp cloth and a mild deter-

gent to wipe all grease-laden surfaces. Read the Silverstone

label on the bottom cover. It has instructions for care and cleaning

of the Silverstone

surface. Use care when cleaning blower wheel

- it must not become bent or misaligned. DO NOT ALLOW WATER

TO ENTER MOTOR. Make sure all surfaces are completely dry

before re-installing filters and restoring power.

Motor is permanently lubricated. Do not oil or disassemble motor.

CLEANING

Fan and Lights: 3 push button switches for each. Push any button

to select one of 3 fan speeds or one of 3 light levels. Push the

same button to turn fan or light off. Press another button to change

fan speed or light level. A light above each fan button indicates the

fan speed.

Heat Sentry: Your range hood is equipped with the Heat Sentry

feature, which monitors temperature. The Heat Sentry will auto-

matically turn the fan on at its highest speed when the tempera-

ture is above normal.

1) If a fan setting is selected when the Heat Sentry in on, the light

above the fan button will flash on and off.

2) If the fan setting is off when the Heat Sentry is on, the light above

fan button 3 will flash on and off rapidly.

After the temperature has lowered to normal, the fan will change

to the setting prior to the Heat Sentry turning on.

Fuse: The hood control contains a fuse to protect it from power

surges. If the fuse has opened (blown), the green fan-level indica-

tors will operate properly when the fan buttons/switches are

pressed - but the fan and lights will not turn on.

The fuse is a 5 x 20 mm, 3 Amp, Fast-Acting, 125V (min.). Common

manufacturer and part numbers are: Littlefuse, 235003; Bussmann,

GMA3; Wickmann, 1911300002. Radio Shack, Digikey (1-800-

344-4539), and most electronic supply stores have them in stock.

To replace the fuse:

1. Disconnect power at service entrance.

2. Remove filters, bottom panel, light wire harness, and air chute.

3. Remove and inspect fuse. If it is

not open (blown), additional

diagnostics need to be done.

4. Install new fuse.

5. Re-assemble air chute, light wire harness, bottom panel, and

filters.

6. Turn on power and check hood/control operation.

Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com

kitchen

accessories

U N L I M I T E D

rangehoods

com

is a division of

Broan at

rangehoods

com

1 2 3 4 5 6

Comments to this Manuals

No comments

Best K8087 User Manual Page 5

Comments to this Manuals

Related products and manuals for Cooker hoods Best K8087